Aprilaire Outdoor Temperature Sensor Installation
Aprilaire Outdoor Temperature Sensor Installation - • do not route wire alongside 120vac wires. The sensor can be used with the aprilaire 8570, 8870 or 8600 thermostats. Web heat pump units use the outdoor air temperature sensor to shut down the heat pump and go to auxilary heat when the outdoor temp drops below a certain set point (usually set at around 35f) most standard heat pump units are inefficient below 35f although some have been designed to produce heat at much lower temps. • do not mount closer than three feet to any exhaust vent. Web my aprilaire 600 humidifier was installed with the outdoor temperature sensor placed in an inlet air duct (6 diameter, insulated, running about 12 feet to the outside wall). Web outdoor temperature sensor (odt) the temperature sensor can be located in the fresh air duct, in the vent inlet, or on the outside of an exterior wall.
System setting #05 (remote sensor) is used to enable sensor. Place above the snow line. Do not install inside outdoor condensing unit. Web • heat blast® raises the room temperature 3°f to 5°f. Web your aprilaire humidifier control is installed in the cold air return.
AprilAire Z10ODT Wireless Outdoor Temperature and Humidity Sensor for
The sensor can be used with the aprilaire 8570, 8870 or 8600 thermostats. Web your aprilaire humidifier control is installed in the cold air return. Do not install inside outdoor condensing unit. • do not mount in direct sunlight. System setting #05 (remote sensor) is used to enable sensor.
AprilAire Z10ODT Wireless Outdoor Temperature and Humidity Sensor for
Locate the aprilaire model 8052 sensor on the side of the building out of direct sunlight (see figure 3). Web your aprilaire humidifier control is installed in the cold air return. Make sure all components are present (see figure a): Place above the snow line. Save this manual for future reference.
Aprilaire Outdoor Temperature Sensor Installation Best Guide Hvacreboot
Web • use to monitor air temperature (return or supply duct, outdoor, freezers, wine cellar). Web the 8052 outdoor or duct mount temperature sensor is used to monitor or control temperature. Web for aprilaire® humidifier installation, follow aprilaire humidifier installation instructions. • optional wireless outdoor temperature sensor available. Web outdoor temperature sensor (odt) the temperature sensor can be located in.
AprilAire Z10ODT Wireless Outdoor Temperature and Humidity Sensor for
System setting #05 (remote sensor) is used to enable sensor. Web outdoor temperature sensor (optional) outdoor temperature can be measured by attaching an 8052 sensor to the s1 and s2 terminals. Heat pump applications can use the outdoor temperature to effectively utilize the heat pump: The sensor can be used with the aprilaire 8570, 8870 or 8600 thermostats. Or should.
Aprilaire 8052 Outdoor/Duct Mount Temperature Sensor 686720805202 eBay
Place above the snow line. System setting #05 (remote sensor) is used to enable sensor. Place at least 3' away from exhaust vents and condensing lines. A second sensor located on the outdoor coil is used to measure the coil temperature. Heat pump applications can use the outdoor temperature to effectively utilize the heat pump:
Aprilaire Outdoor Temperature Sensor Installation - A second sensor located on the outdoor coil is used to measure the coil temperature. Web installation outdoor temperature sensor (optional) outdoor temperature can be measured by attaching an 8052 sensor to the sl and s2 terminals. Web for aprilaire® humidifier installation, follow aprilaire humidifier installation instructions. • use to monitor water by affixing it to outside of water pipe and insulate. System setting #05 (remote sensor) is used to enable sensor. It is important to anticipate a drop in outdoor temperature and reduce the setting accordingly to avoid excessive condensation.
• use to monitor water by affixing it to outside of water pipe and insulate. It is important to anticipate a drop in outdoor temperature and reduce the setting accordingly to avoid excessive condensation. Web for aprilaire® humidifier installation, follow aprilaire humidifier installation instructions. Web your aprilaire humidifier control is installed in the cold air return. Web outdoor temperature sensor (odt) the temperature sensor can be located in the fresh air duct, in the vent inlet, or on the outside of an exterior wall.
Web Heat Pump Units Use The Outdoor Air Temperature Sensor To Shut Down The Heat Pump And Go To Auxilary Heat When The Outdoor Temp Drops Below A Certain Set Point (Usually Set At Around 35F) Most Standard Heat Pump Units Are Inefficient Below 35F Although Some Have Been Designed To Produce Heat At Much Lower Temps.
Web • use to monitor air temperature (return or supply duct, outdoor, freezers, wine cellar). • optional wireless outdoor temperature sensor available. Do not install inside outdoor condensing unit. Place above the snow line.
• Do Not Route Wire Alongside 120Vac Wires.
Locate the aprilaire model 8052 sensor on the side of the building out of direct sunlight (see figure 3). Place at least 3' away from exhaust vents and condensing lines. The sensor can be used with the aprilaire 8570, 8870 or 8600 thermostats. Web your aprilaire humidifier control is installed in the cold air return.
System Setting #05 (Remote Sensor) Is Used To Enable Sensor.
If an ahc is to be installed. Place above the snow line. For example, with an outdoor temperature of 20° the correct setting will be 35% relative humidity. Do not install inside outdoor condensing unit.
• Do Not Mount In Direct Sunlight.
Web my aprilaire 600 humidifier was installed with the outdoor temperature sensor placed in an inlet air duct (6 diameter, insulated, running about 12 feet to the outside wall). A second sensor located on the outdoor coil is used to measure the coil temperature. It is important to anticipate a drop in outdoor temperature and reduce the setting accordingly to avoid excessive condensation. Or should the sensor go all the way to the outside.